Custom professional walking belt for treadmill 2.4mm

Custom professional walking belt for treadmill 2.4mm

Manufacture in 24-48 hours

Free give away of the lubricant for the first lubrications of your treadmill walking belt.

Can choose between 250ml of silicone oil or 400ml of treadmill walking belt spray.

By default we send 250ml of silicone oil, but if you prefer the spray write "lubricating spray" in the order comments (just before choosing the payment method).

How to measure your band:

Measure the width.

Method 1: With the belt in tension (installed):

Make a mark with a pen about 3 / 5cm from one side, then measure one meter long and make another mark. Move the walking belt by hand or foot and measure another meter again. Repeat this process until you reach the first mark.

Look at the two screws that hold the tensioner roller to know how many centimeters of tension they have to adjust the manufacture of your belt as much as possible.

Example: If the tensioning screws are tightened by 3 centimeters, this indicates that we must manufacture the walking belt between 4 and 5 cm shorter, otherwise when tightening the band it could have problems.

Method 2: With the walking belt cut or untensioned:

Carry out the same measurements as in method 1 but we will only reduce the measurement taken by 1 or 2 centimeters.

Ex: We have measured the cut band and it gives us 2600mm long, we recommend ordering a 2580mm or 2590mm band.

Method 3: I don't have the band:

Loosen the tensioner roller bolts all the way or until the roller touches the wood. Pass a non-elastic string or thread around the outside of the two rollers (as if it were the walking belt), tension this thread and make a mark, then measure the thread.

Example: This measure is the minimum manufacturing measure, in this case it is recommended to add between 1 and 2 cm to avoid problems when installing the band.

** IT IS RECOMMENDED TO ALWAYS REVIEW THE MEASURES TAKEN 2 OR 3 TIMES **

** Each manufacturer uses different models of walking belts and there are those that expand more or less over time, there are those that do not.

** The conditions of use, lubrication, humidity, dryness by the sun, etc. .. can also affect the dilatation.

Details of the main technical characteristics of the tapestry belt for treadmills

Repuestosfitness offers telephone advice for the installation of the new belt.

Whenever the walking belt is changed, the status of the walking deck must be checked. If the state of the table is not adequate, we advise to change or rotate it if there is the possibility of using it on both sides. A walking deck in poor condition can deteriorate the belt more quickly. In case of doubt, contact us.

The walking belts need periodic maintenance (tension, centering of the belt, ...), as well as frequent greasing with special silicone oils, the quantity and periodicity of the greasing will depend on the use of the belt, location of the center, type of greasing used, etc

Repuestosfitness recommends using special silicone oil or spray for treadmills. (Lubricants and Oils)

Our walking belts are compatible with all machines on the market, such as the following brands;

Bh, Bodyguard, Bodytone, Cardiozone, Challenger, Circle, Cybex, Epic, Fitness Gear, Freespirit, Freemotion, Gac Planet, Gervasport, Golds, Healthrider, Horizon, Image, Kettler, Keyfitness, Landice, Lifefitness, Matrix, Nautilus, Nordictrack, Pacemaster, Precor, Proform, Quinton, Reebok, Salter, Schwinn, Sole, Spirit Fitness, Sportsart, Stairmaster, Startrac, Technogym, Tempo, Tunturi, Vision Fitness, Weslo.

If you cannot find the band you need or need more information, please contact us.

RepuestosFitness

(+34) 604 182 66

pedidos@repuestosfitness.com